Customer Service:

(800) 421-5830
customerservice@mkdiamond.com


MK Twitter Link
Scarifiers

MK Scarifiers have been designed to leave a clean, textured or rough finish on any type of concrete or asphalt surface. Drums are available to provide cleaning, texturing, leveling, grooving and paint removal. The unique engage/disengage lever allows the operator to raise and lower the drum without losing the depth setting. Drums are interchangeable and provide for fast and easy changeover.

Scarifier Features:

  • Designed for scarifying, roughening, planing, leveling, smoothing, or creating grooves in concrete surfaces
  • Can be used to remove paint or coatings, and to clean and prepare concrete surfaces prior to coating, re-coating, and floor covering installation
  • Rugged sand casting and heavy gauge steel construction
  • Precision adjustable depth control
  • Engage/disengage lever allows operator to raise and lower the cutter drum without changing depth setting
  • Quick-change drum
  • Depending on cutting wheel style, production rate varies from 350 to 500 square feet per hour for a 1/8-inch removal depth
  • One-year limited warranty
Drum Configurations SG-9 SG-5
5 Point Carbide Drum 158941 165276
6 Point Carbide Drum 158942 165277
18 Point Steel Drum 158943 165278
12 Point Steel Drum 158944 165279
Blank Drum (no cutters) 158532 158533
Specifications SG-9 SG-5
Engine*/Motor Honda GX270 Cyclone ABB (Baldor) 5 hp 230V
Weight (including drum) 170 lbs. (77 kg) 170 lbs. (77 kg)
Drum Dimensions (Dia. x L) 6" x 8" 6" x 8"
Drum Weight 30 lbs. (14 kg.) 30 lbs. (14 kg.)
LxWxH (inches) 23" x 20" x 43" 23" x 20" x 43"
LxWxH (mm) 813 x 508 x 1,092 813 x 508 x 1,092



Warning: This equipment contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. These chemicals are contained in various components. fluids and paint including but not limited to fuel, oil, electric motors and batteries. In addition, gasoline/diesel powered equipment emits engine exhaust and fumes, and when serviced, cleaned or maintained generate used oil, waste fluids, fumes, grease, grime and particulates from the component wear and silica dust which contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Five Tooth Carbide Tip Star
  • Used for grinding, leveling, grooving, cleaning, and preparing concrete
  • Five-point carbide tips (1-3/4" OD x 5/8" ID)
  • Longer life than steel tooth cutters, average of 6000 to 8000 square feet
  • Maximum cutting rate is 1/8" per pass

Six Tooth Carbide Tip Star

  • Used for grinding, leveling, grooving, cleaning, and preparing concrete
  • Six-point carbide tips (1-3/4" OD x 5/8" ID)
  • Exceptional life, average of 8000 to 10000 square feet
  • Maximum cutting rate is 1/8" per pass

18 Tooth Steel Sharp Tooth Cutter

  • Used for general cleaning of concrete or asphalt including removal of paint, epoxy, urethane, adhesive, and heavy dirt, grease and oil deposits
  • 18 tooth hardened steel, (2" OD x 5/8" ID)
  • Average life of 500 to 800 square feet
  • Maximum cutting rate is 1/16" per pass

12 Tooth Steel Blunt Tooth Cutter

  • Used for paint and oil removal, traffic and shop floor safety-line removal, cleaning and concrete preparation
  • 12 tooth, hardened steel (2" OD x 9/16" ID)
  • Average life of 500 to 800 square feet
  • Maximum cutting rate is 1/16" per pass
* Engine power ratings are calculated by the individual engine manufacturer and the rating method may vary among engine manufacturers. MK Diamond Products makes no claim, representation or warranty as to the power rating of the engine on this equipment and disclaims any responsibility or liability of any kind whatsoever with respect to the accuracy or the engine power rating. Users are advised to consult the engine manufacturer’s owners manual and website for specific information regarding the engine power rating.
Click on thumbnails for enlarged images.